Currently Available: Need a skilled Software Developer for your next project?
Categories
Self-Hosting

What to Do When Synology Security Advisor Reports Malware on Your NAS

A malware alert in Synology Security Advisor means a security check found malicious software or activity on the NAS. Investigate the alert, but remember that it does not show how an attacker got in, what data they accessed, or whether the entire NAS is compromised.

Open the detailed scan result and read the exact rule, detected item, and recommended action. If Security Advisor offers Fix, Synology says that action instructs it to remove detected malware. If the report points to a backdoor or a compromised system, or you see ransomware or unauthorized file changes, treat the NAS as compromised. Limit further access, preserve useful information, and plan to recover from a backup the incident did not reach.

Read the specific finding

Security Advisor checks Synology NAS devices against security rules in DSM, Synology’s operating system. The overview of Security Advisor groups those checks into categories. These include Malware and System, along with Account, Network, and Update.

Read the Malware rule’s details instead of relying on the overall scan status. Synology uses Danger when Security Advisor finds malware and recommends action. At Risk means the NAS has high-risk security settings, while Warning means it has lower- or moderate-risk settings. An Out-of-date status concerns DSM updates. By itself, that status does not mean Security Advisor found malware.

Note the rule name, severity, any reported files or accounts, and the recommended action. Also record when the scan ran and which DSM version the NAS uses. If the alert came by email, sign in to DSM through your usual trusted route and check the report there before acting on the message.

Use Fix, then scan again

If the report identifies malware and shows a Fix button, use it and follow any other recommendations in the result. Then run Security Advisor again and review the new report. The Security Advisor results documentation says Fix instructs Security Advisor to remove detected malware.

Do not delete a system file or account just because its name looks suspicious. Contact Synology Support if the alert remains after you use Fix, names a backdoor or system change, or gives an unclear recommendation. Keep the report details and relevant logs so Support can assess the finding.

A false positive is possible, but an earlier case does not explain a current alert. Synology documented a specific 2015 case in which Antivirus Essential quarantined a system file and triggered a Security Advisor warning. The advisory describes an issue on older DSM versions that Synology has resolved. It does not show that current malware alerts are commonly false.

Isolate the NAS when you see signs of compromise

A malware alert alone does not confirm a ransomware attack. If someone is changing files without authorization, you see ransomware, or the report says the system is compromised, disconnect the NAS from the local network to limit further access. If you cannot disconnect it, Synology’s ransomware guidance says to power it down. Powering down can erase evidence stored in temporary memory, so save relevant logs and report details first if doing so will not delay containment.

For a serious incident, contact Synology Support and involve the person responsible for IT security or an incident-response professional. Record what you saw and when it began. Note which accounts or shared folders seem affected, along with what you have done so far. Decide whether you need further investigation or evidence before resetting the NAS.

Check which backups the incident could reach

A backup is useful only if the attack did not change it. Ransomware can affect any drive or network share the compromised NAS could access. The attack could not reach a drive that was disconnected or powered off. A connected drive or share that the NAS could write to may have been exposed.

Leave disconnected backup drives disconnected while you contain and investigate the incident. Synology recommends checking potentially affected external drives and scanning them from a computer confirmed to be clean before opening files. If logging for the relevant protocol was enabled before the incident, check DSM Log Center for file-transfer deletion events. If logging was off, the lack of those events does not prove that no files were deleted.

Check whether Snapshot Replication or Hyper Backup has a restore point from before the suspected attack. If you do not know when the attack began, Synology recommends choosing an earlier restore point. Do not reconnect a backup drive just to see whether it looks normal.

Reset only when the NAS itself was compromised

Use a factory reset to recover a compromised NAS, not as a routine response to every Security Advisor alert. Synology’s ransomware recovery guidance tells users to reset the affected NAS, reinstall DSM, and restore data from backup when the NAS itself was compromised.

The reset erases data: Synology says it erases data on the drives, including DSM and volume data. Before resetting, confirm that you have a usable backup the incident did not reach. Also decide whether Support or an incident-response professional should review the case. After rebuilding the NAS, change account passwords and review permissions and services exposed outside the network.

Patch and reduce remote access

After you contain the incident and remove the threat, update DSM and installed packages. Review account permissions and turn off services you do not need. Synology also recommends limiting publicly open ports, using a VPN for remote management instead of exposing DSM management ports directly, and enabling protections such as Auto Block and multifactor authentication. Its NAS security recommendations describe these measures.

On October 29, 2026, Synology reported ransomware attacks targeting devices that ran outdated DSM versions with a vulnerability patched in December 2024. That report supports keeping DSM current; it does not identify the cause of any particular Security Advisor alert.

What I'm building

Delegate tasks. Get software.

Give Vroni a GitHub issue, bug report, spec, or rough idea. It reads the repo, plans the change, writes code, runs checks, and works toward a review-ready pull request.

Take a look at vroni.com

Email updates

Usually a new article and a few links I found interesting.

No spam. Unsubscribe with one click.

Leave a Reply

Your email address will not be published. Required fields are marked *